General
High Dynamic Range mode (“HDR”) for RSPdx-R2 use below 2MHz
Highly integrated native Windows support for the SDRplay family
Multiple ‘virtual receivers’ for simultaneous reception and demodulation of different types of signals within the same receiver bandwidth
An integrated frequency scanner (for frequency ranges and stored memory panel lists)
A selectivity filter with an ultimate rejection greater than 140dB.
A unique distortion-free double stage AGC with fully adjustable parameters
AFC for FM signals
Multiple notch filters with BW adjustable to 1Hz + Notch Lock feature
A unique synchronous AM mode with selectable/adjustable sidebands, dedicated PLL input filter, & selectable PLL time constants
SNR (stereo noise reduction), featuring a proprietary noise reduction algorithm for stereo broadcast
Powerful wideband noise filter for addressing common sources of RFI (e.g. power supplies, internet over DSL etc.)
Calibration for receiver frequency errors
RDS support optimised for low signal environment
Active Noise cancelling
CAT and Omnirig control
Calibrated RF Power Meter with > 100dB of usable range
Calibrated S-Meter supporting IARU S-Meter Standard
The ability to save power (dBm) and SNR (dB)
Measurements over time, to a CSV file for future analysis
IQ output accessible for 3rd party applications
General
Weight
315g
Size
113mm x 94mm x 35mm
Low current consumption
190mA @ >60MHz (excl Bias T)
120mA @ <60MHz (excl Bias T)
Connectivity
USB 2.0 (high speed) type B socket
Frequency Range
Continuous coverage 1kHz – 2GHz
Antenna A Port Characteristics
1kHz – 2GHz operation
50Ω input impedance
SMA female connector
Antenna B Port Characteristics
1kHz – 2GHz operation
50Ω input impedance
SMA female connector
Selectable 4.7V DC out (see Bias T)
Antenna C Port Characteristics
1kHz – 200MHz operation
50Ω input impedance
BNC female connector
Antenna Port Isolation
Unselected port isolation 40dB min
Reference Clock Input
MCX female connector
Bias T (Antenna B Port only)
Software selectable 4.7V @ 100mA
IF Modes
Zero IF, All IF bandwidths
Low IF, IF bandwidths ≤ 1.536MHz
IF Bandwidths (3dB)
200kHz
300kHz
600kHz
1.536MHz
5.0MHz
6.0MHz
7.0MHz
8.0MHz
ADC Characteristics
Sample frequency 2 – 10.66MSPS
14-bit native ADC (2 – 6.048MSPS)
12-bit (6.048- 8.064 MSPS)
10-bit (8.064- 9.216MSPS)
8-bit (> 9.216 MSPS )
Maximum Recommended Input Power
0dBm continuous
10dBm for short periods
Reference
High temp stability 0.5PPM TCXO
In-field trimmable to 0.01PPM
External Reference Clock
Plug in the external clock before power-up. Auto-detect will switch to the external reference.
Frequency 24MHz sine/square wave
1V Pk-Pk Min
3.3V Pk-Pk Max
Typical Noise Figures
19dB @ 300kHz
18dB @ 2MHz
17dB @ 12MHz
15dB @ 25MHz
15dB @ 40MHz
2.6dB @ 100MHz
2.1dB @ 200MHz
6.0dB @ 340MHz
3.1dB @ 660MHz
4.4dB @ 1500MHz
5.0dB @ 1800MHz
Notch Filters
FM Notch Filter
>30dB 77 – 115MHz
>50dB 85 – 107MHz
>4dB 144 – 148MHz
MW Notch Filter
>15dB 400 – 1650kHz
>30dB 500 – 1530kHz
>40dB 540 – 1490kHz
DAB Notch Filter
>20dB 155 – 235MHz
>30dB 160 – 230MHz
Note: The notch filters above are software selectable and remove specific broadcast bands.
Front End Filtering
Low Pass
500kHz
2MHz
Band Pass
2-12MHz
12-30MHz
30-60MHz
60-120MHz
120-250MHz
250-300MHz
300-380MHz
380-420MHz
420-1000MHz
High Pass
1000MHz